1112 (3IBT) Stuffing Box For 2" Pipe
Galvanized Tee Not Included In Price
$ 135.00   BUY ON-LINE

Windmill stuffing boxes are brass packing boxes that are screwed into a tee at the top of the well. The packing box is packed with graphite rope packing around the stuffing box rod, and a packing nut is tightened down to secure the graphic rope packing around the rod. This lubricates the rod, and prevents leakage from the top of the stuffing box.

1-1-7/8"       $  141.00

2-1/4"          $  174.00

2-3/4"          $  261.00

The #852 seamless brass heavy duty cylinders are deep well units. These open top cylinders come with solid brass bronze ball valves and 4 leather plungers. Plungers are tapped so they can screw into the check valve for easy removal. Longer strokes are available upon request. 

The #449 all brass open top cylinders are made with seamless brass tubing available in 11 gauge brass tubing. Our cylinders come with solid bronze ball check valves and 3 leathers on the plunger. Plungers are tapped so they can screw into the check valve for easy removal. Longer strokes and some larger sizes are available upon request.

1-1-7/8"       $  113.00

2-1/4"          $  143.00

2-3/4"          $  222.00

Complete Open Top Brass ​Cylinder Assembly 449 / 852

Diameter &          Barrel       Casing      Drop Pipe       Rod
​S
troke Length    Length      Min. I.D.         Size            Size

Secures Drop Pipe To The Top Of A Well Using A Windmill And Cylinder

449 Ball Valve Complete Bottom Check Assemblies

Diameter &         Barrel      Pipe Size     Rod Size 
S
troke Length    Length

1014   1-1/4" Stuffing Box (7/16" Rod) 
 $ 112.00     
BUY ON-LINE

1034   2" Stuffing Box (7/16" Rod)
 $ 129.00     BUY ON-LINE

1044   2" Stuffing Box (Heavy Service)  5/8" Rod  
$ 322.00      BUY ON-LINE 

1054   2-1/2" Stuffing Box (Heavy Service)  7/8" Rod
$ 354.00      BUY ON-LINE

1064   3" Stuffing Box (Heavy Service)  7/8" Rod  
$ 375.00      BUY ON-LINE

Pictured is our cylinder with submersible pump assembly for installation under a windmill. This assembly will allow your windmill to pump water with wind power when there is enough wind available. When the wind is not sufficient to pump water with the windmill, you can switch the electric powered submersible pump on to supply the water. You can either use a gas powered generator or standard electric power to run the submersible pump during low wind conditions.

Only the highest quality components are used in this assembly. All piping and fittings shown are brass. The cylinder is an all brass construction with a brass ball valve and a brass ball check. We have found that ball valves react better than poppet valves when pumping water through the cylinder with a submersible pump. The submersible pump used in this system is our deluxe stainless steel Flint & Walling S-model pump with Franklin Electric's stainless steel submersible motor. The assembly prices shown below include everything pictured to the left.

1-11/16" x 10"          18"          2"                   1"             7/16"      $   168.46

1-13/16" x 10"          18"          2"                   1"             7/16"      $   168.46
2" x 10"                    18"          2-1/2"             1-1/4"       7/16"      
$   200.91
2-1/4" x 10"              18"          3"                   1-1/4"       7/16"     
$   224.09
2-1/2" x 10"              18"          3"                   1-1/4"       7/16"     
$   241.82

3" x 10"                    18"          3-1/2"             1-1/4"       7/16"      $   318.19
3" x 12"                    20"          3-1/2"              2"            7/16"     
$   326.37
4" x 13"                    20"          4-1/2"              2"             5/8"       
$   540.00 

3-Leather Complete Ball Valve Plunger Assemblies

2"              $  58.00

2-1/4"        $  66.00

2-1/2"        $  70.00

3"              $  91.00

Complete Brass Cylinder Assembly - 442

10MP  Pump Flange For    1"        Well Size     $  68.30

11MP  Pump Flange For    1-1/4"  Well Size     $  63.30

13MP  Pump Flange For    2"        Well Size     $  68.54

14MP  Pump Flange For    2-1/2"  Well Size     $  75.45

15MP  Pump Flange For    3"        Well Size     $  69.37

16MP  Pump Flange For    4"        Well Size     $  75.57

17MP  Pump Flange For    5"        Well Size     $  82.60

18MP  Pump Flange For    6"        Well Size     $  88.80

1/2 HP   10 GPM   Depths to 225'   $ 1140.00
1/2 HP     5 GPM   Depths to 350'   $ 1280.00

3/4 HP    10 GPM  Depths to 350'   $ 1290.00

 1   HP    10 GPM  Depths to 450'   $ 1388.00  

When The Wind Doesn't Blow You Can Still Have Water
"Open Top Brass Cylinder With Submersible Pump Back Up"

a DENVER WINPUMP COMPANY

2-Leather Complete Plunger Assemblies

  • Open Top All Brass Cylinder
  • All Brass Fittings & Strainer
  • Flint & Walling SS Submersible Pump
           End & Franklin Motor 

The Shallow Well #442 water well cylinders are closed top cylinders designed for smaller diameter shallow depth wells made with 11 Gauge seamless brass tubing.  
The #442 plunger is all brass with hemispherical poppet; the check poppet is fitted with a special facing for a secure seal.

#3 Inverted Brass Tube Stuffing Box has a 1-1/8" inside diameter brass tube that is 18" long. The top brass connection is threaded 2" male iron pipe thread. The brass piston has two 1-1/8" leather cups on a 5/8" steel plunger rod with standard 5/8" rod threads. This IBT stuffing box can accommodate up to a 12" stroke. Larger diameter brass tubes and longer strokes are available on request.
The #3 Inverted Brass Tube Stuffing Box uses 1-1/8" leather cups with a 5/8" center hole. The leather cups are installed on the rod with the top one facing up, and the lower one facing down. Up is like the leather was a cup with a hole in the bottom. Down is like the cup was upside down drying and has a hole in the bottom.

1-1-7/8"       $    84.00

2-1/4"          $  112.00

2-3/4"          $  181.00

Diameter &         Barrel      Pipe Size     Rod Size 
S
troke Length    Length

1-7/8" x 14"             24"              2"              5/8"      $  290.91
1-7/8" x 20"             30"              2"              5/8"     
$  311.82 

 2-1/4" x 19"             30"           2-1/2"           7/8"      $  408.19 

  2-3/4"x 18"              30"              3"              7/8"      $  586.36  

NOTE: Use Galvanized Steel Pipe Only For Windmill Drop Pipe - PVC Pipe May Bend Causing The Cylinder To Wear Uneven Or Bend The Pump Rod and Cause The Cylinder To Lock And Not Pump

An U.S.A. Corporation

Textable Ordering

4-Leather Complete Ball Valve Plunger Assemblies

Brass well cylinders and parts

Sub-Cylinder Adapter Only.
Not all components are shown in this picture but are included in the package price. Requires minimum 4" ID well casing.


$185.00

1-7/8" x 36"             48"              2"              5/8"       $  447.00
                                                                         
BUY ON-LINE
2-1/4" x 36"             48"           2-1/2"           7/8"       
$  569.00
​                                                                         
BUY ON-LINE  

2-3/4" x 32"             48"               3"             7/8"       $  757.00

​                                                                          BUY ON-LINE

Cylinder Capacity Chart
Click To Enlarge